Looking for a Mazda ABS pump, ABS control module, DSC module or complete ABS hydraulic unit?
Mazda vehicles use ABS (Anti-lock Braking System) together with DSC (Dynamic Stability Control) and traction control systems to help maintain braking performance and vehicle stability.
A faulty ABS pump or electronic control module can cause ABS, DSC and traction control warning lights, hydraulic pump faults, brake pressure sensor faults, communication errors and internal control module faults.
At AutoPulse247, we supply genuine used OEM Mazda ABS pumps, ABS control modules and complete ABS/DSC hydraulic units for a wide range of Mazda vehicles.
Our stock may include ABS pumps and modules for:
Mazda 2, Mazda 3, Mazda 5, Mazda 6, CX-3, CX-30, CX-5, CX-7, CX-9, MX-5, RX-8, BT-50 and other Mazda models.
Different ABS/DSC units may be fitted to vehicles of the same model and year, so always compare the part numbers on your original unit before purchasing.
Mazda ABS and DSC systems can generate different diagnostic trouble codes depending on the model, year and ABS unit fitted. Some commonly searched ABS-related fault codes include:
C0020 – ABS Pump Motor Control
Possible ABS hydraulic pump motor, wiring, power supply or internal ABS unit fault.
C0031 / C0034 – Wheel Speed Sensor Circuit Fault
Usually associated with a wheel speed sensor, wiring, connector or sensor signal problem. These codes do not normally mean the ABS pump itself is faulty.
C0037 / C003A – Wheel Speed Sensor Circuit Fault
Can indicate a rear wheel speed sensor, wiring or signal problem depending on the Mazda model.
C0044 – Brake Pressure Sensor / Circuit Fault
May indicate a brake pressure sensor or hydraulic control unit problem on applicable ABS/DSC systems.
C0061 – Lateral Acceleration Sensor Fault
Associated with the vehicle stability/DSC sensor system and does not necessarily indicate an ABS pump failure.
C1095 – ABS Hydraulic Pump Motor Circuit Failure
Can indicate an ABS pump motor, electrical circuit or hydraulic control unit problem.
C1288 – Brake Pressure Sensor / ABS-DSC System Fault
On applicable Mazda systems, this can relate to brake pressure sensing or the ABS/DSC hydraulic control system.
U0121 – Lost Communication With ABS Control Module
The vehicle has lost communication with the ABS/DSC control module. Possible causes include a failed module, wiring, CAN Bus, power supply or ground problem.
U0415 – Invalid Data Received From ABS Control Module
Another vehicle control module has received invalid information from the ABS/DSC module.
Depending on the Mazda model, diagnostic equipment may also report faults relating to:
Codes involving an ABS pump motor, internal control module, brake pressure sensor, hydraulic unit or loss of communication can sometimes indicate that the ABS/DSC unit requires repair or replacement.
However, an ABS fault code does not automatically mean the ABS pump is defective. Battery voltage, fuses, wiring, connectors, grounds, CAN Bus communication and related sensors should be checked first.
If the fault remains after these checks and diagnostics confirm an internal ABS/DSC unit failure, replacement may be required.
AutoPulse247 supplies used genuine OEM Mazda ABS pumps, ABS control modules and complete ABS/DSC hydraulic units for Mazda 2, Mazda 3, Mazda 5, Mazda 6, CX-3, CX-5, CX-7, CX-9, MX-5 and other models.
For the best match, search using the complete Mazda, ATE, Continental, Bosch or FoMoCo part number from your original unit.
If you are unsure, send us your VIN, ABS fault code and a clear photo of the original ABS unit label.
Important: Fault-code definitions can vary between Mazda models and ABS/DSC generations. Always confirm the code against the diagnostic information for the specific vehicle before replacing the ABS unit.
